44 Reviews View type:
Fits:- HONDA glom
- HONDA DIO110 JF58
- HONDA PCX150
- HONDA PCX125
- HONDA LEAD125 JF45
It is very convenient to start the engine with the side stand still in place.Read More- Fits:
- KAWASAKI NINJA250 13-17 EX250L
- KAWASAKI KSR110
- KAWASAKI KLX250 98-16
- KAWASAKI KLX125 10-16
- KAWASAKI D-TRACKER-X 08-16
- ...and more.
Even if you fall down on a Gymkhana runIt was added to prevent the brake from becoming unusable.Even if it doesn't do the Guard function for you.It's a Recommendation because it can be a dress-up of t...Read More - Fits:
- HONDA GROM 16-
- HONDA GROM (MSX125) 13-15
I've fallen over twice in the Mini circuit and so far it's been perfectly fine. (Lol)Read More - Fits:
- HONDA GROM (MSX125)
- HONDA MONKEY125 (JB02-1000001-)
I bought this when I changed the DriveSprocket on my MONKEY125 from 15T to 16T. If you don't plan on going back to 15T, you can process the OEM and you'll be fine, but if you're in the process of sett...Read More - Fits:
- HONDA GROM (MSX125)
A company in the US called DRIVEN seems to be a sponsor of the MOTARDTeam! But it's not just Mini bikes such as the Grom and Z125, it's also the middle class We have developed and sold a variety of dr...Read More - Fits:
- HONDA GROM JC61-1300001-
- HONDA GROM JC75-1000001-
- HONDA MSX125 SF
- HONDA MSX125 MLHJC618_D5000001-
- HONDA GROM JC61-1000001-
- ...and more.
When I lowered the ride height by 2 inches, it seemed to fall over on the OEM STAND.Easy to install, easy to adjust the height!But it's just too expensive!Read More - Fits:
- HONDA GROM (MSX125) (JC61)
When the car falls over, the plastic part of the tip is shaved off to reduce the damage to the car. But in fact, the entire resin part was blown off! (Lol) I'll look for other products.Read More - Fits:
- HONDA GROM (MSX125) (JC61)
The pentagonal Cap to be installed on the Center is Bolt to Body It is the Spec. that fixes it in the body, but because the screw thread on the body side is resin, it is easy to lick it, and it is not...Read More - Fits:
- HONDA GROM 16-
- HONDA GROM (MSX125) 13-15
To be honest, I bought it just for looks. It sticks out quite a bit on the side, but it gives you a custom lookIn normal step, the snare is very good It is no longer a hitRead More - Fits:
- HONDA GROM 16-
- HONDA GROM (MSX125) 13-15
The original intention was to be prepared for a fall, but fortunately it has not been taken care of yet It's not surprising that the function of the Quantity:Pair (for Left and Right) It is quite over...Read More - Fits:
- HONDA Grom
- HONDA Grom MSX125
Adjustable for MONKEY125 side stands switch I was looking for a stand and I found this product I bought this stand for Grom and installed it as it is almost compatible with MONKEY125 It looks good and...Read More - Fits:
- HONDA GROM 16-
- HONDA GROM (MSX125) 13-15
I bought it to prevent it from falling over, but when I installed it, it looks accent and customI didn't have the tools to install it, so I had it installed at the store where I bought the grommets In...Read More - Fits:
- KAWASAKI Z125 PRO
- HONDA Grom
I bought it without reading the description because of the image, and when it arrived, Quantity:2pc. There was only SetThe image shows the four Front and Rear Sets, but the description is Quantity:1 S...Read More - Fits:
- HONDA Grom 13-16
Installation may be a little confusing The Mount is much different, but that's about itThe shape is a bit obvious I think they looked tighter in the same colorI'm sure there is some reason for this I ...Read More - Fits:
- HONDA Grom 16-
There is a high probability of grounding the switch box if you fall to the Right in the groms And the potsch to align with the handlebar hole will be collapsed and the Switch box& amp;Throttle holder ...Read More - Fits:
- HONDA GROM (MSX125) (JC61)
An instruction manual is not included for installation, but the If you can pull out the front axle shaft, it's easy to installRead More - Fits:
- HONDA GROM (MSX125) (JC61)
It was solidly built for the priceInstallation instructions are not included, but the Rear axle If you can pull out the shaft, it should be easy to installRead More - Fits:
- KAWASAKI Z125
- HONDA GROM 125
- KAWASAKI KSR110
- HONDA New Model GROM
- HONDA MSX125 SF
- ...and more.
Have tried to upload a picture three times now but I cannot get the thing to load like last time so I can only write about the latest piece of sexy polished aluminium that now graces my 2015 Honda Gro...Read More - Fits:
- KAWASAKI Z125
- HONDA GROM 125
- KAWASAKI KSR110
- HONDA New Model GROM
- HONDA MSX125 SF
- ...and more.
Depending on the up / down direction, you can not access Nut.The paint of the part which it receives once and twice is peeled offAn unpleasant person purchased a M6 hexagon socket separatelyRead More - Fits:
- HONDA Grom
- HONDA Grom MSX125
Although there was no problem with the installation of the Body, the mounting part of the Side stands switch was slightly different from the OEM, and it was necessary to adjust several Washers on the ...Read More
?
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING