Once you select the option, estimate delivery time will be displayed.
*Shipping date and Estimate time of arrival are not guarantee.
Once your orders are placed, we will check the stock of manufacturer and send you the confirmed Shipping time via e-mail.
[Separately required parts for installation] Either of the following throttle holder sets is required. ・Yoshimura Racing Throttle Holder Set for TMR Large Body (L=850mm) ・Yoshimura Racing Throttle Holder Set for TMR Small Body with Switch (L=850mm) (Switch side coupler wiring required to be changed)
[Parts required separately] ・Yoshimura Oil Breather Tank Kit ・Insulator Band (40-60) ・GPz1100f air cooled intake manifold (KAWASAKI stock)
*The length of the throttle wire is the standard setting.Please note that it may vary depending on the installation method. *Images are for reference only. *If the fuel cock interferes with the installation, it may be possible to avoid it by replacing the cock with an external cock such as Pingel (not available for vehicles with fuel pump). * Please note in advance that cancellation and/or return of this product cannot be accepted once the order has been placed.
* This item can not be cancelled, returned nor exchange after placing an order.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
OEMCarburetor to TMR replacement. There was a rumor that the setting was difficult to get out, the diameter of TMR36 was too large for 750, the driving was hurried, and it was not suitable for town driving, etc. There was also worry, but it can run with the setting at the time of shipment for the time being. At present, there is no problem at all in Idling - low speed - middle speed and town driving only by the adjustment of Pilot screw. The temperature is high, and it is a little dense, but I think that I will do it while enjoying the setting. Compared to the OEM Carburetor, the Response and Acceleration when you open the Axel is completely different. The Axel is also much lighter than the OEM.View Detail
I installed it on my Z1. It's a replacement for the CR33, but it's as if Motorcycle became something else. "Sharp. It will be It can be driven normally with a pontoon, but the Throttle is much lighter, and at first it will thump as if it were High Solo. I think you will be surprised if you open it with the same feeling as CR. But you will get used to it if you run a little. If you are not used to it, you can make it low slung to make it easier to operate. With the benefit of the Acceleration Pump, the feeling of acceleration is just amazing and makes you incredibly agile. Setting is easy ... . The carburetor body is designed not to wear out, so the body can be used for a long time ... . But if you are not sure, I think you should try it without thinking about the details. If you like to run, you won't regret installing it. It's a FlatValve, but it has a rounded shape, so it looks very good on older cars. In the case of Z1, Indicator needs to be replaced of course, but Throttle holder is OEM (Ripro) and could be installed without any problem. The Manual is also described in a very detailed and helpful way. One bad point is that Throttle Wire is hard to hang compared to CRetc. I think it will be a moderate struggle until you get used to it. However, once you install the engine and run the engine, you will be able to feel the difference.
I love the mattiness and look of the CR and will continue to enjoy it while changing it, but once you run with the TMR you will be amazed at its performance. Motorcycle (especially old cars) "Run. It's definitely a Carburetor that should be an option if you like the I was lucky enough to get it very cheap this time at WehBig's Sale...View Detail
If only VSeal's secondary air problem could be solved, the Power feeling, Torque, Response, The best carburetor in terms of fuel economy and everything, and surprisingly easy to set up, FCR It's also good because the body is not designed to be worn out like a And you can adjust the acceleration pump and Cut (Just pull out the shaft.) The difference between Yoshimurabrand and Mikuni is Just a Sticker?View Detail
I think that this price is attractive. Since it is already set up, unlike CR you can run even with an amateur even with an amateur. If it's not enough, you may want to set it up with Pro shop.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!