09-12 09-12(FI cars)*Side caps can be used with the stock ones.
GRASS TRACKER Big Boy
-08 (Carburetor)*Drilling of switch holes is required. |*It is necessary to change the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo.
GSX400
05-07 GK7CA *Processing of the switch hole is required|* You can use the normal side cap.
Made in Japan.Prototype, installation confirmation and mass production are all under in-house management.These handlebars are made with a great deal of care and attention to detail, including careful selection of materials, several types of polishing, engraving of part numbers, high-precision bending and welding, and high-quality surface treatment, based on technology and know-how cultivated over many years in Osaka in Japan.STKM13A steel material with excellent tensile strength is used.Cleared by JMCA safety standard value.Triple nickel and chrome plating (3 layers of nickel and chrome) finish with thick film and excellent durability and corrosion resistance.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
The Yamaha Y's Gear, which is slightly lower than the NORMAL and is attached with Option:The SR Moderate Screen now stands out. It seems to be compatible with Posh-Classical Rear Sets though the run is not yet done. It seems to be. I'm looking forward to the actual run.View Detail
I decided to make KATANA Up Handlebar from low back pain etc, but I thought that I do not want to break the style of Separate handle and purchased it. The diaphragm of OEMSeparate handle was about 40-Degrees, this product was the most restricted 32 degrees you looked for. Top Bridge changed for NPROject's Up Handlebar and installed. The width fits within the range of the automobile inspection certificate with the Bar End attached, it moves up to 15 centimeters each, and the body goes up. It was enough to reduce the burden of the waist. The load on the front wheels is reduced correspondingly, and the handlebar operation becomes unreasonable. I think that until you get used to, Cornering etc. I think that it is better to step forward by consciously.View Detail
[Webike Monitor] by it being broad, and also hanging down to a Grip position and the angle being attached in case of the Handlebar attached with present vehicle,A state is behind brought [ that a Knee grip is not effective and ] at the time of acceleration,When trying to stand on a Step to absorb unevenness of a road surface in a knee, a weight shift must be carried out because a Grip position passes before a hand,It purchases by having thought that it would exchange for the low thing which also has narrow width so that a Riding position may not suit me in any way and the load of it can be carried out to the Front side to a slight degree.Although it was uncomfortable at first when run after exchanging the > Handle, it got used immediately and was a very good feel. A riding posture turns into an inclined attitude lightly, an old problem is solved because especially the Grip position became low and the width of the Handle also became short 10 cm, and a run is also a Sporty.A Plating of the product itself is also beautiful and has no something to say. It is although it is better if processing is however carried out stop shifting.View Detail
The SR400'07 model was equipped. the thing which has a few angle and which is low to a slight degree and hangs down by normal being high and hanging down since the angle is large -- it considered and made it this handle. compared with the normal of SR, it is somewhat low, and hangs down, and there is no angle -- almost -- a flat -- a few is extracted to the front. Although it becomes a low and near position, a riding posture does not change mostly. Height, an angle, and an iris diaphragm are exquisite and ride very easily. Incidentally, since SR does not have the projection of positioning in a switch box and did not need to make a hole in the handle on the occasion of handle exchange, the point was easy.View Detail
Fits: HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
On the LeftGrip side, there is a paper seal with the product number, ManufacturerMain and product name, which is still difficult to remove. If you could make it easier to peel off, I'd appreciate it. Also, when I peeled off the seal, I found a hole in it. I don't understand why there is a hole in it.
Also, I'd appreciate it if HURRICANE would do an OrderHandlebar or something!View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!