Once you select the option, estimate delivery time will be displayed.
*Shipping date and Estimate time of arrival are not guarantee.
Once your orders are placed, we will check the stock of manufacturer and send you the confirmed Shipping time via e-mail.
The standard stroke for the Monkey and Gorilla is about 55mm. When installing a down suspension of 30mm or more, in order to increase the stroke. We recommend the use of lower spring holders for down springs. Dax and Chaly are sold at the same time, but are designed differently from this product. The stock spring also has different load capacity, wire diameter and pitch from Monkey and Gorilla. Our original springs are made with spring rates that are suitable for each type of vehicle. The same spring for Monkey and Dax will not be provided with different length. This product is completely different from those sold in certain online auctions.
This spring is specially designed for Monkey and Gorilla for stock forks. The fluffiness of the front end has been eliminated, and there is a sense of tenacity that cannot be compared with the stock, You can open the door at a high speed. However, it does not have a stiff and thrusting behavior in the low speed range. This is also recommended for those who had reinforced suspension but it was too bouncy and uncomfortable to ride. [Features of Cuby's original reinforced spring] 1] You may think that 30% is a little too hard, but it feels softer when you make it. However, when the engine brake is applied from the speed range before three digits in actual driving The chattering vibrations from the front end of the vehicle will be stopped by this. (When the wear condition of the fork inner parts is normal) 2] The end face of the spring has been machined to make it easier to insert the spring. 3] Stock spring is analyzed, and the material is the same as the stock spring, load in use, stress in use, Calculates the spring constant (spring rate). 4] Made in Japan (domestic production).
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
Решил обслужить и обновить пружины на передней подвеске своей Honda Monkey. Взял стандартный размер, чтобы все осталось в стоке. Подходит отлично, быстрая установка. Всем рекомендую. Любимый Webike покупай больше этих пружин - мои друзья тоже хотят их заказать, но их мало в наличии. Спасибо тебе и возможно купить такой товар. I decided to service and update the springs on the front suspension of my Honda Monkey. I took the standard size so that everything would remain in the drain. Fits perfectly, quick installation. I recommend it to everyone. My favorite Webike, buy more of these springs - my friends also want to order them, but they are few in stock. Thank you and it is possible to buy such a product.View Detail
These springs are a low cost but big improvement for your small bike. The quality is better than oem I believe and really helps with firming up the ride when you lower the bike. It he greatly improved the handling. Installing the springs is easy with basic knowledge and can be done quickly. Packaging was very good and boxed well so it was safe during air freight which was very fast.View Detail
The installation has been done a few times with Gorimont FFork Parts Replacement Grease Replacement, so It's easy to remove from the Fork and divide it into two parts, but this is the first time I've removed the Fork Spring So when I watched Net and grabbed the game, I was grilling between the Vise and the Vise, and it didn't just miss, it went on and on I couldn't help myself, so I used a sander to cut it off I put it on the Vise stand and realized it was Opposite Thread Screw, so the second one was I managed to remove it with a lot of force Installation is done in reverse order and then you can put the Grease to Quantity:Pair (for Left and Right) You can paint it in evenly (I make sure to apply the Grease so that no air gets into the Spring place every time I'll put it in.) I grabbed the FBrake to see how much spring pressure I could get before the ride, and then I moved it up and down I felt it was quite hard, but there is no feeling of rattling at all when I started riding There is no NORMAL Full Bottom and no pompom when Brake is on (By the way, I installed an absorber on One Side.) I was able to drive my MONKEY at 60km with the Pi Pass as it is a second class Number The braking is now better than the NORMAL Plus Absorber One last word, Moldy's packaging was very clean and BigliView Detail
After replacing the Rear shock, I became more aware of Front's poorness, Also, curing of Dust Seal - Crack crack, Grease leak was also terrible, Overhaul In addition I introduced Reinforced Spring.
OEM Length (30% strengthening) Although I put things of, It became solid and stable, stable - I feel secure..
Since the work process and the tool to be prepared falls a lot on the net, it is omitted.
Upper / There is some hang to desorb Spring from LowerSpring holder. Between the desk vice, we strike the conch and Spring end part with Graver or Slotted screwdriver. I do not need much power, but I can not come off unless I hit it to some extent.
Even when you wear Reinforced Spring in Holder, Spring with vice and turn Holder in Wrench, you can incorporate it in the lake. Because I did not take out the Spring end BALI, Although I scraped the Holder with crackling, I installed it without worrying about it. Perhaps you should treat the neighborhood as a chitin. Also, assuming Wheel assembly time, the orientation of the Inner pipe - It is better to pay attention to the angle.
If you prepare the tool properly in advance, the work itself is not difficult at all, I think that it would be better to replace the OEM Parts Number as a part of Overhaul, but to feel the benefit of Reinforced Spring more.
Finally, since the work is endless, it is black and it is attached with an old Grease like a mass of mud, It is good to prepare Dustcloth for more.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!