*Please make sure to check the size of the handlebar on your vehicle. *Regarding the installation of GT handlebar *Inner diameter of bar end is Φ13.5. *If the position is too high or too far back, it may be necessary to replace the cable or harness.In addition, if the position is lowered too much or moved forward too much, it may interfere with the tank, cowl, etc. when the handlebars are fully locked. There is no hole for the switch box.
It was developed for comfort on long rides. A high-dimensional balance of rigidity and flexibility has been achieved to provide a moderate degree of flexure and suppress micro-vibration. It is made of high-strength aluminum alloy and the size is most suitable for on-road models with bar handles. The position grid is laser-printed to enable proper positioning. The sandblasted processing increases the strength of the product's surface, and the matte texture gives it a luxurious feel. ・Titanium color anodized finish ・Stock diameter bar (22.2mm) is available The highly visible position gauge facilitates angle adjustment.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I bought this one for dress-up purpose of HORNET250. The Position is slightly different from the OEM, but it's only an error level, so I couldn't tell much… The texture was so tasteful, it didn't feel cheap at all! The only thing is that the color is a little more pink than I was expecting. I'm sure you'll love it! When I install it on the HORNET, I don't have to change the length of the cables or do any processing at all, so it doesn't cost me any extra money. But please note that this is not drilled, so you need a tool that can drill holes to install it! I asked the shop to install everything because of that. It has been about 3 years since I installed it, but I don't see any deterioration over time, so I think I can use it with confidence.View Detail
I'm using it on my Kawasaki ZR-7 When I bought the car used, it had a POSH Super low bar on it, and then I was riding with ZETA's Bar rise kit (19mmUp), but I had the Cowl In putting it on, I replaced it with this Handlebar I have no experience with OEM positions, but the Grip position is higher and closer than before My upper body is now awake There may be an effect of Cowl, but the position change also helps to reduce fatigue It seemsView Detail
I used it for the Bar handle of GPZ900RNINJA. I thought it would be a little wide, but it's a good fit without being cut. The texture is not cheap and the look is satisfactory for me personally.View Detail
I want to increase the height and the aperture from the standard Handlebar of MT-03, and consider Size etc I did and bought a low type-2 The fit is perfectly fine However, the Throttle Cable and Clutch Cable do not arrive as standard (I can't judge the Brake hose as I had changed it to Long beforehand.) I bought a 75mm Long Cable, but I thought about 50mm Long would be just fine It is You can use the 75mm Long with no problem if you change the way you handle it
But it might be better if it was another inch or so farther away It's a personal preference here, so if there's a good one, I'll replace itView Detail
Purchased this because I wanted Short Bar for WR 250X. Although it seemed not to be exclusive items, it attached without problems. It was still good if the color had a bit more black eye Titaniumium color.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!