7,602.1 NGN
(811 JPY)
3 (1 Reviews)
rating breakdown
5 Stars |
|
0 |
4 Stars |
|
0 |
3 Stars |
|
1 |
2 Stars |
|
0 |
1 Stars |
|
0 |
Average
I wouldn't be surprised if you dropped it at any time.This is another PetitDress- found at KITACO and ConvenienceParts upItems. upItems. it's totally dress-up, because for practical purposes I don't need this kind of Cap. However, I thought it was well made for that purpose. Anyway, the body is Material:It's aluminum and has been properly treated with anodized aluminum, so the color and The shine is good. Normally, the Bolt cover is made of soft plastic, but it is not made of aluminum. Since it is not deformed, the O-ring is inserted into the hexagonal hole of the Cap bolt with it. This is a good example. The part where the O-ring is properly fixed has a groove digging, and it takes a lot of time and effort to process it. I'm there, so I guess it's no wonder it's so expensive.
However, this O-ring is a tricky one. The one for the smallest M6 Screw has a very small O-ring. So it was Large strange for me to fit it in with my old eyes. And it's probably because of the airtightness of the O-ring. Sometimes it would fall off on its own after a few seconds of fitting. No matter how many times I pushed it in, it would fall in such a way that it would come off of itself. As I observed, it seems that the air between this Cover and the Bolt's hexagon hole is compressed and the force The O-ring seems to be pushed back in. That's how airtight the O-ring is. As I was TRYING, there was apparently a point where the air inside was released and the push back phenomenon was The Large threshold type makes it difficult to push in. I hit it with a plastic hammer and pushed it in (I may not be able to get it off later).
However, I felt that the risk of falling due to vibration while driving was Large. It is not at present, but I must be prepared to lose it. At that time, I have no choice but to buy the replacement parts and deal with it.
I used 4 bags this time, and the cost was about 3,500 yen. Well, it's a good cost-benefit ratio for a dress-up, isn't it, using Pinpoint I think you can be satisfied with it even if you don't have a lot of them. However, because I think that it is not strange when it disappears, I think that other custom parts purchase You might want to buy a spare while you're at it.
Most Viewed Reviews Of K-CON Cap Bolt Cover
Very Good
Bolt Cover 12mmthis item is well made and all but the gold color is like more orange than gold, however i like how it looks in my bike. regards!View Detail
Very Good
To prevent rust.MirrorMounting Bolt tightening holes
There was a pool of water and Rust.
I bought a Cap!
There was one with and without a rubber at the end of the cap, but
The part to be used this time is the Bolt that attaches to the horizontal direction
So, is it Large sturdy without Rubber? I think so.
Does the size fit since it's a special bolt?
I was worried, but the Exactly/Fit
This way, there's no water pooling in the car wash or rain.
It won't rust and is safe.
Quantity needed:2pc. Against the Set
Quantity:1 Set of 4pcs.:2pc. The Set becomes a spare part.
It was a waste of time to find a usable part of the
I couldn't find anything.
Quantity:1 Set of 2pcs. products would also be available.
Thank you.
View Detail
Very Good
Add a splash of colorAttached to the end of the Rear Sets
I was worried about the rust on the Bolt, so I took the rust off.
I treated it with paint, but it's a place where water tends to accumulate
I've decided to install the Cap.
If you're going to install it.
RedAnodized in conjunction with Bar End!
The end ends are nice and consistent.
There are two required numbers, but the quantity:1 Set of 4pcs.
Quantity:2pc. Set too much
I'm just trying to make sure there's no...
In case the worst happens and you drop it or put a Wound on it.
That's the part you want to keep in reserve.
View Detail
Other Reviews From Japanese Webike user
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING